Toshiba 24W1333G

Good Morning:
I am Carlos from Portugal, and I would like to know if you can help me, I will try to write in English because I do not know anything about Romanian, I apologize.
I have a Toshiba TV model 24W1333G, 17MB95S-1 V.1 211212 panel Chimei Innolux V236 BJ1-LE1 Rev. C2 and it did not connect with the command.
I made a firmware update and it started to work, but the image was inverted vertically!
Then I updated the firmware with a pendrive, and from there no longer worked, not even the led appears.
Is it possible to recover the TV or is it dead?
I have CH341 programmer, and SPI eproom new, you will also need to program the nand chip, and how do you do?

Thanks so much for your help.

Click : [Trebuie sa fiti inscris si conectat pentru a vedea acest link]

I upload for you this software HERE.
It is a software for usb stick. Do you know the procedure?

Good Morning :
  I am very grateful for your help, and responding to both, I have to say that it is very difficult for me to understand your language, I have to be always copy / paste of your messages to Google translator, hence I apologize if something not be doing well, or if they do not understand my problem.
Mesersmith I do not know how to do this by usb stick, so thanks for help.
Another thing, the tv does not bear any testimony of being fading, (led power), only the source power with the correct tensions.

Many thanks and all the best to you.
Carlos

Carlos, if you understand english, is ok. Also, if you want to read in our forum, you colud open in Chrome and install a dictionary to translate automatically.

So, extract de archive in a root of a usb pen drive, unplug tv, introduce the pen drive in usb, do not plug the tv yet, press and hold ok button from remote and then plug the tv in the socket.
The stand by led will start to blink rapidly and when it did this, relase the ok button and wait until tv restarts.

Thanks for everything but I'm about to give up.
I formatted the pendrive in fat, not ntsc or fat32, then I extracted three files to this pendrive, mb90_en.bin; mboot.bin; usb_auto_update_A1, the pen has nothing more than these three files.
I inserted the pen into one of the usb slots, pointed the command to the IR receiver and pressed the OK button, held it, and then inserted the power plug into the socket.
I waited for about thirty seconds and nothing at all.
Anyway thank you for your help.

Ps: I'm using an RC "madeforyouweb", not the original, and when it worked tv, but with the inverted image I had to put a file of this command vestel mark.
I'll schedule Vestel to see if I can get in.

Carlos

Try it, it's for SPI flash MX25L1605
HERE

Good night, Daniel.

Thanks for your help, but I already tested this soft. The TV has turned on, but it continues with the inverted image, when I try to disconnect or connect with remote control it does not always work, I have to disconnect by removing the plug from the power outlet, and I can not enter the service menu, nor make any changes.
I inserted the soft with a CH341 programmer, without removing the chip, soldered small wires in the integrated legs, the CH341 correctly detected the chip, I deleted this one and then put the one that I had already downloaded from the forum.
When I try to put an update with a pendrive, and following all instructions, from formatting the pen to putting the software, nothing happens.
This TV seems to be doomed, or haunted.
Another crap from the Vestel factories !!!

Thanks
Carlos

Good morning CARLOS,
It does not hurt to try this from a finlux with the same main board / screen combination.
[download=www.filehost.ro/3172823513/17MB95S_V236BJ1_LE1_C2_17IPS61_FINLUX_24LEDDVD_ELK_2014_08_13_rar/">17MB95S_V236BJ1_LE1_C2_17IPS61_FINLUX_24LEDDVD_ELK_2014_08_13_rar][/download]

Good afternoon everyone;

It is with great joy that I tell you that today, and with your software, I was able to get the TV to work.
To all who helped me, thank you very much, if you come to Oporto I will pay you for lunch!
Please to moderators close topic



Thank you very much

Carlos